[QE-users] Calculating U parameter for Ni in LiNiO2 using hp.x
Timrov Iurii
iurii.timrov at epfl.ch
Wed Sep 16 10:29:49 CEST 2020
Dear Mohammad,
> By changing the threshold values you mentioned, nscf calculation finished (no "cholesky" error)...
Great!
> ...but there is divergence in computing "chi".
The HP calculation for q points #1 and #2 has converged, but the problem is for the q point #3. In the HP input, please setup
alpha_mix(1) = 0.1
and try again.
Also I suggest to use the default value nmix = 4, because I have never tried changing it to something else (you are using nmix=5) and so I do not know what to expect.
Also note that the parameter conv_thr_chi = 1.0d-8 is very tight, so can try even something like conv_thr_chi = 1.0d-6 which should also be fine (because your calculations take a lot of time with 16 cores that you use).
Greetings,
Iurii
--
Dr. Iurii TIMROV
Postdoctoral Researcher
STI - IMX - THEOS and NCCR - MARVEL
Swiss Federal Institute of Technology Lausanne (EPFL)
CH-1015 Lausanne, Switzerland
+41 21 69 34 881
http://people.epfl.ch/265334
________________________________
From: users <users-bounces at lists.quantum-espresso.org> on behalf of Mohammad Moaddeli <mohammad.moaddeli at gmail.com>
Sent: Wednesday, September 16, 2020 7:21:53 AM
To: Quantum ESPRESSO users Forum
Subject: Re: [QE-users] Calculating U parameter for Ni in LiNiO2 using hp.x
Dear Iurii,
By changing the threshold values you mentioned, nscf calculation finished (no "cholesky" error), but there is divergence in computing "chi". Please find the link below. All input and output files are attached.
https://drive.google.com/file/d/1TWDQ3X_jG7HsgaVvhUiu3oVWt28g3DNz/view?usp=sharing
Best,
Mohammad
ShirazU
On Sun, Sep 13, 2020 at 2:13 PM Timrov Iurii <iurii.timrov at epfl.ch<mailto:iurii.timrov at epfl.ch>> wrote:
Dear Mohammad,
1.In the SCF input for the supercell you have:
conv_thr = 1.0d-20
This is extremely low! Try some value in-between 1.0d-10 and 1.d-15.
2.In the HP input for the supercell you have:
ethr_nscf = 1.D-14
This is also extremely low! Try the default value of 1.0d-11.
If you still have a problem when using e.g. conv_thr=1.d-10 and ethr_nscf=1.d-11 then please put input and output files on Google Drive or Dropbox and send a link to us (do not forget to check the permissions of the shared folder).
HTH
Iurii
--
Dr. Iurii TIMROV
Postdoctoral Researcher
STI - IMX - THEOS and NCCR - MARVEL
Swiss Federal Institute of Technology Lausanne (EPFL)
CH-1015 Lausanne, Switzerland
+41 21 69 34 881
http://people.epfl.ch/265334
________________________________
From: users <users-bounces at lists.quantum-espresso.org<mailto:users-bounces at lists.quantum-espresso.org>> on behalf of Mohammad Moaddeli <mohammad.moaddeli at gmail.com<mailto:mohammad.moaddeli at gmail.com>>
Sent: Sunday, September 13, 2020 6:12:27 AM
To: Quantum ESPRESSO users Forum
Subject: Re: [QE-users] Calculating U parameter for Ni in LiNiO2 using hp.x
Dear Lorenzo,
Thank you for your prompt reply.
Using qe_6.6 (in which calculating force and stress is implemented) the 221 supercell relaxed with the U obtained from the output of hp.x for the primitive cell, but the same error appeared. What do you recommend?
Best,
Mohammad,
ShirazU
On Mon, Sep 7, 2020 at 12:07 PM Lorenzo Paulatto <paulatz at gmail.com<mailto:paulatz at gmail.com>> wrote:
> I am trying to calculate the U parameter for Ni in LiNiO2. The hp.x
> (qe_6.5) runs without any error for the primitive cell, however the
> "problems computing cholesky" error occurs for running a 2×2×1 supercell
The most likely cause is that you did a mistake in the atomic position
or cell size.
kind regards
--
Lorenzo Paulatto - Paris
_______________________________________________
Quantum ESPRESSO is supported by MaX (www.max-centre.eu/quantum-espresso<http://www.max-centre.eu/quantum-espresso>)
users mailing list users at lists.quantum-espresso.org<mailto:users at lists.quantum-espresso.org>
https://lists.quantum-espresso.org/mailman/listinfo/users
_______________________________________________
Quantum ESPRESSO is supported by MaX (www.max-centre.eu/quantum-espresso<http://www.max-centre.eu/quantum-espresso>)
users mailing list users at lists.quantum-espresso.org<mailto:users at lists.quantum-espresso.org>
https://lists.quantum-espresso.org/mailman/listinfo/users
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.quantum-espresso.org/pipermail/users/attachments/20200916/cd8a2078/attachment.html>
More information about the users
mailing list