[QE-users] [EXT] Environ Bands Not Converging

Andreussi, Oliviero Oliviero.Andreussi at unt.edu
Thu Nov 1 23:46:52 CET 2018


Hi,

Thanks for reporting the problem. I am not sure of its source, but the defaults of Environ should be good enough for simple systems like yours and if you tested different numerical parameters without success this would suggest me that there is a physical reason why the calculation is not converging. My main guess is that the problem resides with the lithium ion. Have you tested the calculation without lithium? Have you tried the calculation with lithium and without the solvent? What pseudo potential are you using for lithium (does the lithium ion have just one valence electron or does it also have its core electrons)?

If lithium has only its valence electron and loses it to the substrate, this is probably going to be a problem for SCCS. In SCCS the continuum boundary is defined on the electronic density, so it means that the continuum goes on top of the lithium ion. To avoid this you could either use full potential for lithium or use an alternative approach for the continuum interface, namely the soft-sphere solvation approach (Fisicaro et al. JCTC 2017). To use the latter you can just specify solvent_mode = ‘ionic’. In this case, you may want to check that the soft-sphere radius for lithium is reasonable.

Hope this helps.

Best,

Oliviero Andreussi
--
Assistant Professor
Department of Physics
University of North Texas
Email: oliviero.andreussi at unt.edu<mailto:oliviero.andreussi at unt.edu>
Phone: +1-(940)-369-5316
Skype: olivieroandreussi
Web: https://sites.google.com/site/olivieroandreussi

On Nov 1, 2018, at 5:28 PM, Lance Kavalsky <lance.kavalsky at mail.utoronto.ca<mailto:lance.kavalsky at mail.utoronto.ca>> wrote:

Hello all,

I am currently trying to use Environ and am experiencing difficulty. When running vc-relax I am receiving the error "bands not converged". This is despite changing the environ_thr, tol, solvent_mode, conv_thr, diagonalization, and mixing_mode. I have yet to see it complete a single full scf cycle, and watching the estimated scf accuracy it will periodically explode hitting values as large as 1700 Ry before finally giving the error message.

Any additional suggestions would be very much appreciated. Both the pw.x and environ.in files have been pasted below. I am using QE 6.2.1 and Environ 1.0.

Thanks,
Lance Kavalsky
University of Toronto



&control
    disk_io='high'
    tprnfor = .TRUE.
    restart_mode = 'from_scratch',
    prefix = 'all',
    calculation ='vc-relax',
    outdir = './all',
    Pseudo_dir = '~/qe_pseudo'
    nstep = 1000000

/

&system
    assume_isolated = 'slabz'
    ibrav=0,
    nat=33,
    nbnd=120
    nosym= .TRUE
    ntyp=2,
    ecutwfc=60,
    degauss=0.02,
    occupations='smearing'
    smearing='mp'
    vdw_corr='grimme-d2',
/

 &electrons
    mixing_mode='local-TF',
    mixing_beta=0.2,
    electron_maxstep=200,
    conv_thr = 1.D-5
/

&ions

/

&cell

/

CELL_PARAMETERS

  18.638982356   0.000000000   0.000000000
  -9.319491169  16.141832210   0.000000000
   0.000000000   0.000000000  43.442244346

ATOMIC_SPECIES

C 12.0107 C.pbe-n-kjpaw_psl.0.1.UPF
Li 6.94   Li.pbe-s-kjpaw_psl.0.2.1.UPF

ATOMIC_POSITIONS angstrom

Li       2.465903098   2.847312956   7.998767559
C       -0.001222067  -0.002150713   5.748168621
C       -0.006894107   1.419668805   5.748711907
C       -1.235385692   2.135486140   5.748168054
C       -1.235385692   3.559103273   5.748168054
C       -2.465827629   4.271813207   5.747820607
C       -2.465827488   5.694593503   5.747451858
C       -3.697991730   6.405978452   5.747822309
C       -3.699995777   7.827928911   5.748170451
C        2.465832575  -0.007964030   5.748711231
C        2.465830973   1.415317747   5.733405805
C        1.225702627   2.131306376   5.733413904
C        1.225702627   3.563283037   5.733413904
C       -0.006894107   4.274920608   5.748711907
C       -0.001222067   5.696740126   5.748168621
C       -1.233668925   6.405976111   5.747821630
C       -1.231667255   7.827928014   5.748169206
C        4.932884056  -0.002150957   5.748168156
C        4.938555745   1.419665120   5.748705064
C        3.705961632   2.131305141   5.733395741
C        3.705961632   3.563284272   5.733395741
C        2.465830973   4.279271666   5.733405805
C        2.465832575   5.702553443   5.748711231
C        1.231662375   6.408544130   5.748170451
C        1.233666422   7.830494589   5.747822309
C        7.397488816  -0.000004090   5.747451858
C        7.397488675   1.422776206   5.747820607
C        6.167048845   2.135488891   5.748165854
C        6.167048845   3.559100522   5.748165854
C        4.938555745   4.274924293   5.748705064
C        4.932884056   5.696740370   5.748168156
C        3.699990897   6.408545027   5.748169206
C        3.697989227   7.830496930   5.747821630


K_POINTS automatic
4 4 1 0 0 0



environ.in


&ENVIRON
environ_type='input',
env_static_permittivity=7.58
environ_thr=5.0
/
 &BOUNDARY
solvent_mode='full'
/
 &ELECTROSTATIC
   pbc_correction = 'parabolic'
   pbc_dim = 2
   pbc_axis = 3
   tol = 1.D-13
 /




_______________________________________________
users mailing list
users at lists.quantum-espresso.org<mailto:users at lists.quantum-espresso.org>
https://na01.safelinks.protection.outlook.com/?url=https%3A%2F%2Flists.quantum-espresso.org%2Fmailman%2Flistinfo%2Fusers&data=02%7C01%7Coliviero.andreussi%40unt.edu%7Cf72fbeaa20b14de78d3508d640496841%7C70de199207c6480fa318a1afcba03983%7C0%7C0%7C636767081366404963&sdata=Baje%2B2x4jfbGUspCi5JC6M3UwnInEq%2FBEbRtxEuKFwM%3D&reserved=0

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.quantum-espresso.org/pipermail/users/attachments/20181101/325bb5f5/attachment.html>


More information about the users mailing list