[Pw_forum] PW.X WORKS ONCE AND NEXT TIME DOESN'T.. FOR THE SAME INPUT FILE..
siddheshwar chopra
sidhusai at gmail.com
Tue Jul 15 09:45:25 CEST 2014
Dear Sir,
Yes I too had the same doubt that ecutrho syntax must be a problem. Thanks
for the help Sir.
Actually I am using a script file to run for different "ecutrho" values.
ecutrho=$ecut*8;
and then ecutrho=$ecutrho inside &system
Could you tell me what wrong I am doing here?
Regards,
On Tue, Jul 15, 2014 at 11:47 AM, Paolo Giannozzi <paolo.giannozzi at uniud.it>
wrote:
> Syntax "ecutrho=8*20" is not allowed in a namelist
>
> P.
>
> On Tue, 2014-07-15 at 11:00 +0530, siddheshwar chopra wrote:
> > Dear Dr. Giovanni Pizzi,
> >
> > I re ran the i/p file.. i corrected the ecutrho value. But
> > unfortunately the same error persists. Please find attached the i/p,
> > o/p and crash files.
> >
> > I have tried running it from a script and also directly from terminal
> > using "mpirun -n 3 pw.x -i graphene.scf20.in" .
> >
> >
> > Regards,
> >
> >
> >
> > On Mon, Jul 14, 2014 at 9:39 PM, Giovanni Pizzi
> > <giovanni.pizzi at epfl.ch> wrote:
> > Dear Siddheshwar,
> > it is quite improbable that this error did not occur in your
> > first run. You must have changed something between the two
> > runs (and probably forgotten about it).
> >
> > In any case, in the input file you wrote 'ecutrho=' but did
> > not specify any value. This for sure is (one of the possible)
> > causes of the error.
> >
> > Best,
> > Giovanni
> >
> >
> >
> > On 07/14/2014 02:01 PM, siddheshwar chopra wrote:
> >
> > > Dear Users,
> > >
> > > I ran the pw.x successfully using 4 processors. But again
> > > when I am running the same i/p file, I am getting this
> > > error:
> > >
> > > %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
> > > %%%%%%%%%%%%%%%%%%
> > > Error in routine read_namelists (5010):
> > > reading namelist system
> > > %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
> > > %%%%%%%%%%%%%%%%%%%
> > >
> > > stopping ...
> > >
> > >
> ===================================================================================
> > > = BAD TERMINATION OF ONE OF YOUR APPLICATION PROCESSES
> > > = EXIT CODE: 1
> > > = CLEANING UP REMAINING PROCESSES
> > > = YOU CAN IGNORE THE BELOW CLEANUP MESSAGES
> > >
> ===================================================================================
> > >
> > >
> > > Please tell me how to resolve this issue.
> > >
> > >
> > > Regards,
> > >
> > > --
> > > Dr. Siddheshwar chopra,
> > > M.Sc., Ph.D (Physics)
> > > Assistant Professor (Physics),
> > >
> > > Amity University, Noida, India.
> > >
> > >
> > >
> > >
> > >
> > > _______________________________________________
> > > Pw_forum mailing list
> > > Pw_forum at pwscf.org
> > > http://pwscf.org/mailman/listinfo/pw_forum
> >
> >
> > --
> > Giovanni Pizzi
> > Post-doctoral Research Scientist
> > EPFL STI IMX THEOS
> > MXC 340 (Bâtiment MXC)
> > Station 12
> > CH-1015 Lausanne (Switzerland)
> > Phone: +41 21 69 31124
> >
> > _______________________________________________
> > Pw_forum mailing list
> > Pw_forum at pwscf.org
> > http://pwscf.org/mailman/listinfo/pw_forum
> >
> >
> >
> > --
> > Dr. Siddheshwar chopra,
> > M.Sc., Ph.D (Physics)
> > Assistant Professor (Physics),
> >
> > Amity University, Noida, India.
> >
> >
> > _______________________________________________
> > Pw_forum mailing list
> > Pw_forum at pwscf.org
> > http://pwscf.org/mailman/listinfo/pw_forum
>
>
> _______________________________________________
> Pw_forum mailing list
> Pw_forum at pwscf.org
> http://pwscf.org/mailman/listinfo/pw_forum
>
--
*Dr. Siddheshwar chopra,*
*M.Sc., Ph.D (Physics)Assistant Professor (Physics),*
*Amity University, Noida, India.*
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.quantum-espresso.org/pipermail/users/attachments/20140715/c22bb781/attachment.html>
More information about the users
mailing list