[Pw_forum] PW.X WORKS ONCE AND NEXT TIME DOESN'T.. FOR THE SAME INPUT FILE..

Paolo Giannozzi paolo.giannozzi at uniud.it
Tue Jul 15 08:17:53 CEST 2014


Syntax "ecutrho=8*20" is not allowed in a namelist

P.

On Tue, 2014-07-15 at 11:00 +0530, siddheshwar chopra wrote:
> Dear Dr. Giovanni Pizzi,
> 
> I re ran the i/p file.. i corrected the ecutrho value. But
> unfortunately the same error persists. Please find attached the i/p,
> o/p and crash files.
> 
> I have tried running it from a script and also directly from terminal
> using "mpirun -n 3 pw.x -i graphene.scf20.in" . 
> 
> 
> Regards,
> 
> 
> 
> On Mon, Jul 14, 2014 at 9:39 PM, Giovanni Pizzi
> <giovanni.pizzi at epfl.ch> wrote:
>         Dear Siddheshwar,
>         it is quite improbable that this error did not occur in your
>         first run. You must have changed something between the two
>         runs (and probably forgotten about it).
>         
>         In any case, in the input file you wrote 'ecutrho=' but did
>         not specify any value. This for sure is (one of the possible)
>         causes of the error.
>         
>         Best,
>         Giovanni
>         
>         
>         
>         On 07/14/2014 02:01 PM, siddheshwar chopra wrote:
>         
>         > Dear Users,
>         > 
>         > I ran the pw.x successfully using 4 processors. But again
>         > when I am running the same i/p file, I am getting this
>         > error:
>         > 
>         > %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
>         > %%%%%%%%%%%%%%%%%%
>         >      Error in routine  read_namelists (5010):
>         >       reading namelist system
>         >  %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
>         > %%%%%%%%%%%%%%%%%%%
>         > 
>         >      stopping ...
>         > 
>         > ===================================================================================
>         > =   BAD TERMINATION OF ONE OF YOUR APPLICATION PROCESSES
>         > =   EXIT CODE: 1
>         > =   CLEANING UP REMAINING PROCESSES
>         > =   YOU CAN IGNORE THE BELOW CLEANUP MESSAGES
>         > ===================================================================================
>         > 
>         > 
>         > Please tell me how to resolve this issue. 
>         > 
>         > 
>         > Regards,
>         > 
>         > -- 
>         > Dr. Siddheshwar chopra,
>         > M.Sc., Ph.D (Physics)
>         > Assistant Professor (Physics),
>         > 
>         > Amity University, Noida, India.
>         > 
>         > 
>         > 
>         > 
>         > 
>         > _______________________________________________
>         > Pw_forum mailing list
>         > Pw_forum at pwscf.org
>         > http://pwscf.org/mailman/listinfo/pw_forum
>         
>         
>         -- 
>         Giovanni Pizzi
>         Post-doctoral Research Scientist
>         EPFL STI IMX THEOS
>         MXC 340 (Bâtiment MXC)
>         Station 12
>         CH-1015 Lausanne (Switzerland)
>         Phone: +41 21 69 31124
>         
>         _______________________________________________
>         Pw_forum mailing list
>         Pw_forum at pwscf.org
>         http://pwscf.org/mailman/listinfo/pw_forum
> 
> 
> 
> -- 
> Dr. Siddheshwar chopra,
> M.Sc., Ph.D (Physics)
> Assistant Professor (Physics),
> 
> Amity University, Noida, India.
> 
> 
> _______________________________________________
> Pw_forum mailing list
> Pw_forum at pwscf.org
> http://pwscf.org/mailman/listinfo/pw_forum





More information about the users mailing list