[Pw_forum] Recent CVS - problems on SGI

[Carlo Sbraccia]

On Mon, 16 Feb 2004, Konstantin Kudin wrote:

Dear kostya,
try to compile the code with ifc 7.1 and the -CA -CB -CU options and run 
your job again (it will be slower).
Address errors can usually be traced out with the help of these debug 
flags.
carlo

>  This is an update on my previous message. As it turns
> out, one of my jobs under Linux happened to use that
> very same routine "check_constrain", and crashed there
> in the location denoted by "***" below. So while ifc
> 7.1 did compile the code, there is some problem there
> that the SGI compiler seems to have spotted already
> during the compile.
> 
>  Could some F90 expert take a look at that piece of
> the code?
> 
>  Kostya
> 
>   !
>   ! ... if the atomic positions have been corrected
> write them on output
>   !
>   IF ( i > 1 ) THEN
>      !
>      WRITE( stdout, '(/5X,"Corrected atomic
> positions:",/)')
>      DO na = 1, nat
> ***        WRITE( stdout,'(A3,3X,3F14.9)')
> atm(ityp(na)), ( tau(i,na), i = 1, 3 )
>      END DO
>      !
>   END IF
>   !
> 
> --- Konstantin Kudin <konstantin_kudin at yahoo.com>
> wrote:
> >  Hi there,
> > 
> >  I am trying to build the whole O-sesame thing
> > downloaded on Feb. 13 on an SGI Origin, and getting
> > the following error (below). After that the build
> > appears to proceed fine. Any pointers? Or was it
> > just
> > the unlucky Friday the 13th?
> > 
> >  Kostya
> > 
> > P.S. The new "configure" procedure is quite cool!
> > 
> > 
> > f90 -mips4 -64 -O2 -r10000 -r8 -I.
> > -I/scr2/kostya/O-sesame/include
> > -I/scr2/kostya/O-sesame/Modules
> > -I/scr2/kostya/O-sesame/PW
> > -I/scr2/kostya/O-sesame/PH 
> > -cpp -D__SGI -D__SGI64 -D__ORIGIN -D__MPI -D__PARA
> > -D__FFTW -D__USE_INTERNAL_FFTW  -c move_ions.f90
> >  
> > SUBROUTINE check_constrain( alat, tau, atm, ityp,
> > theta0, nat )
> >            ^                                        
> >  
> >          
> > f90-1277 f90: ERROR CHECK_CONSTRAIN, File =
> > move_ions.f90, Line = 296, Column = 12 
> >   Procedure "CHECK_CONSTRAIN" is referenced at line
> > 195 (move_ions.f90).  It must have an explicit
> > interface specified.
> >  
> > f90: MIPSpro Fortran 90 Version 7.3  (f61) Sat Feb
> > 14,
> > 2004  17:20:51
> > f90: 366 source lines
> > f90: 1 Error(s), 0 Warning(s), 0 Other message(s), 0
> > ANSI(s)
> > cf90: "explain cf90-message number" gives more
> > information about each message
> > 
> > 
> > __________________________________
> > Do you Yahoo!?
> > Yahoo! Finance: Get your refund fast by filing
> > online.
> > http://taxes.yahoo.com/filing.html
> > _______________________________________________
> > Pw_forum mailing list
> > Pw_forum at pwscf.org
> > http://www.democritos.it/mailman/listinfo/pw_forum
> 
> 
> __________________________________
> Do you Yahoo!?
> Yahoo! Finance: Get your refund fast by filing online.
> http://taxes.yahoo.com/filing.html
> _______________________________________________
> Pw_forum mailing list
> Pw_forum at pwscf.org
> http://www.democritos.it/mailman/listinfo/pw_forum
>